[ Á¤º¸ ] INTEL D850MD ¸ÞÀκ¸µå BIOS ( ¹öÀü : MV850.10A.86A.0008.P03 ) |
|
2001-09-29 00:00
|
|
|
|
|
|
|
[ Á¤º¸ ] INTEL D850MD ¸ÞÀκ¸µå BIOS ( ¹öÀü : MV850.10A.86A.0008.P03 )
2001.09.27 ÀÏÀÚ INTEL D850MD ¸ÞÀκ¸µå BIOS ÀÔ´Ï´Ù.
º¯°æµÈ »çÇ×Àº
Features/Errata Fixed in This Release
P03-0008
¡¤ Fixed the issue in which the BIOS incorrectly reports that the board can wake via USB from S4 (this is
not possible).
¡¤ Fixed the issue of the RPG Boards that always forces the setup question to S1.
¡¤ Changed banner to P03-0007.
¡¤ Adding new SMM code and I/O APIC support.
¡¤ Added AMI BBS 3.1.
¡¤ Added ITK support.
¡¤ Added processor support
¡¤ Allow CTRL, ALT, and SHIFT key states to be preserved throughout POST, so that shift states will be
available to the OS for Safe Mode entry, bypass startup files.
¡¤ Fixed yellow bang in device manager when PS/2 devices were missing.
¡¤ Fixed a problem where pressing F10 while in Setup caused "Entering Setup..." to appear on the bottom
of the screen.
¡¤ Fix a potential issue where the boot sequence will take longer since the boot data are not correctly
initialized.
¡¤ Added setting of bit1 SMBIOS BIOS Characteristics Extension Byte2 to indicate BIOS support for
function key-initiated network service boot.
¡¤ Fixed problem where some programs were detecting some types of IntelR PentiumR 4 processors as
Intel CeleronR processors.
¡¤ Added WFM 2.0 Remote Lockout support.
¡¤ Added support to boot from network directly if F12 Key is pressed during POST.
¡¤ Updated to rev1.5 of the 82850 memory reference code.
¡¤ Fixed issue where pressing keys during Option ROM scan hangs the system.
¡¤ Fixed issue where the system was always reporting 80-conductor IDE cable type (regardless of actual
cable type) when certain ATAPI devices were connected as the slave device on an IDE channel.
¡¤ When loading custom defaults, the boot order would not always be restored correctly.
¡¤ Fixed issue where ATAPI Removable Devices that support UDMA modes were not getting
programmed for UDMA mode.
¡¤ Fixed issue with a tape backup unit not being seen in Windows 2000 when set as a master and a HDD is
set as a slave on the same channel.
¡¤ Fixed the problem where Custom CMOS defaults cannot be copied correctly to OEM CMOS through
OEM CMOS int 15h function.
¡¤ Fixed an issue where the Fault Tolerant Boot Block Test would fail and not be able to boot if ECC was
enabled during the test.
¡¤ Fixed issue where manufacturing default was incorrect when a CDROM was not installed in the system.
¡¤ Implemented the release of IRQ 12 when the PS/2 mouse is not installed in the system.
¡¤ Fixed issue where system could not transition from S3 to S4 in Microsoft* Windows* operating
systems using the timed Power Options.
¡¤
Ãâó : Intel |
|
|
|
|
|
|
º¸µå³ª¶ó ¸¹ÀÌ º» ´º½º
LGµð½ºÇ÷¹ÀÌ, 4K 240Hz¿Í Full HD 480Hz µà¾ó ¸ðµå Áö¿ø RGB ½ºÆ®¶óÀÌÇÁ OLED ¾ç»ê
Çѹݵµ Àü¸éÀü ±×¸°´Ù, ÄÝ ¿Àºê µàƼ ¸ð´ø ¿öÆä¾î 4 ¿¹¾à ÆÇ¸Å ½ÃÀÛ
AMD ¶óÀÌÁ¨ Z ½Ã¸®Áî¿Í °æÀï, °ÔÀÌ¹Ö UMPC ´ëÀÀ ÀÎÅÚ Arc G-½Ã¸®Áî °ø½Ä ¹ßÇ¥
|
º¸µå³ª¶ó ¸¹ÀÌ º» ±â»ç
¿£ºñµð¾Æ DGX Spark¿Í ¾ÖÇà ¸Æ¹Ì´Ï °Ü³É, AMD ¹Ì´Ï AI ¿öÅ©½ºÅ×ÀÌ¼Ç ¶óÀÌÁ¨ AI ÇìÀÏ·Î °ø°³
°ÔÀÓ°ú AI ¸ðµÎ °¡¼ººñ ³ôÀº ¼±ÅÃ, ÀÎÅÚ µ¥½ºÅ©Å¾ ¼º´É ¿öÅ©¼¥
ȯÀ² »ó½Â ¹× ¹ÝµµÃ¼ ´ë¶õ¿¡µµ ´Ù½Ã ¶³¾îÁö´Â PCºÎǰ °¡°Ý, ±× ÀÌÀ¯´Â?
|
|
|
|
|
|
| ·Î±×ÀÎ | ÀÌ ÆäÀÌÁöÀÇ PC¹öÀü |
|
| Copyright NexGen Research Corp. 2010 |
|
|