우용님 거기 사이트의 방법은 납땜하는거 아닙니다.. |
|
2001-09-26 00:00
|
|
|
|
|
|
|
우용님 제가 알려드린 아래 정보에서 사용된 방법은...
납땜으로 붙여버리는 방법이 아니구요..
거기에 사용된 IC Test Clip 이란게... 가변 저항식으로 된 테스터기 비슷한거 같은데요..
거기 거론된 바로는 이름그대로 클립식으로 되어있어서 납땜 하지 않고 가운데 다리?부분이
클립식으로 되어있어서 그걸 hp6301칩에 끼우고.. 세개의 다리중에 바깥쪽 두개중 아무거나 하나를 납땜으로 선으로 이어서 보드 좌측상단 볼트 고정하는 부분에 접지시키시면 됩니다.
접지시키는것도 납땜할필요없이 전선끝 피복 벗겨서 볼트에 몇번 둘러서 볼트 고정시키면 되는거죠..
결국 보드에는 납땜이 전혀 않되니 나중에 A/S 걱정할 필요없죠..
저두 한번 해보고는 싶은데... 그 가변 IC TEST CLIP이란걸 구할수 있는지 몰라서..
ː지금 얻은 정보이지만 아직 구체적으로 적용된 사진이나 사용기는 없지만
ː해외사이트 게시판에서 읽은 내용을 적어볼려구요 밑에 글이 원문입니다..
ː
ːOK, here we go. To do the voltage mod on the AK-31 you need to go to Radio Shack, and pick up a 47K variable resistor/potentiometer. While your there, get one of these: http://www.radioshack.com/product.a...5Fid=910%2D0228
ː
ːTurn your puter off, and unplug it!
ː
ːConnect the center (of three) terminal on the potentiometer to a wire you have soldered onto the IC Clip you purchased above. Connect one of the outer terminals of the pot to a wire that you have soldered a terminal connector that is suitable to fit under one of your mobo's mounting screws. Get your ohm meter connected to your wires, and turn the potentiometer in the direction that gets you the MAXIMUM resistance. REMEMBER the directions you need to turn it for max/min. Connect the wire with the terminal connector to the mobo mounting screw on the upper left hand corner of your mobo. Connect the IC Clip to leg #7of the "HIP6301CB" Voltage controller IC. It's the one next to the upper left corner of the processor socket. See the attached picture for the correct leg.
ː
ːBoot your machine up into the Voltage/Frequency screen in your bios. Now while watching the voltage monitor, slowly turn the pot in the direction to LOWER the resistance. You will see the voltage rise. I have mine set to 2.2 as maximum. You can now use the bios to LOWER the voltage if you like.
ː
ːGood luck with your new found POWER!
ː
ːOf course, I hold no responsibility for smoke, fire, or electrocution!
ː
ːMy best,
ː
ːDoctor
ː
ːDoctor has attached this image:
ː
ː예전부터 사용해오던 방법대로 저항을 이용해서 한다는데
ː저도 도전해보고싶지만 납땜에는 소질이 없어서 담에 친구놈 불러다
ː시켜야겠네여..
ː근데 개조하시면 A/S 못받거는 아시죠.
ː
ː |
|
|
|
|
|
|
보드나라 많이 본 뉴스
삼성전자, One UI 9.0 업데이트로 갤럭시 S25 시리즈 고속 충전 너프?
MS 윈도우 11 26H2 버전 정식 배포 시작
아마존 중고샵서 RTX 5090 샀더니 쿨러만? PCB 통째로 사라진 제품 배송
|
보드나라 많이 본 기사
메인스트림 게이머의 심리적 마지노선 가격 모델, 라데온 RX 9070 GRE vs RTX 5070 성능 비교
애플의 가변 조리개와 폴더블 스마트폰, 아이폰 18 Pro 시리즈 및 아이폰 듀오 공개
노트북의 게임-허브-로컬 AI 솔루션, 기가바이트 AORUS RTX 5060 Ti AI BOX 제이씨현
|
|
|
|
|
|
| 로그인 | 이 페이지의 PC버전 |
|
| Copyright NexGen Research Corp. 2010 |
|
|